Http://www.Microvision.com.cn Ⅰ、Microvision software introduce
Welcome to the MV professional image processing software, image
analysis for workers in creating a wide range of functions of the
working environment, so that people can easily take on the image
processing, measurement and analysisColor graphics, can be related to the mark to define the color
Graphic switch, show or hide graphics, default is displayed.
Image switch, show or hide the image, is shown by default.
Tailoring the scope of selection, the feature is back and supporting the use of the crop. The scope
of selection, tool selection by dragging the control point (around)
to adjust the selection. In the selection hold down the left mouse
button, can move the selection. Select the image of the need to use
the "Crop" feature.
| |
button, single-click on the button, then click the selected region
alone can cut this region.
"Zoom" button. Every single click once, then zoom in on the basis
of Relevant doubled.
The current ratio of amplification can also be directly selected
magnification
"Narrow" button, single-click each time, on the basis of narrowing in Phase 1 / 2.
"
Show full size" button.
From left to right field followed by measurement tools, measuring amend the Toolbar, tagging Toolbar.
Will use every tool in the context of January 1 after that.
The status bar, then shows the picture of the dimensions of the number of pixels
respectively, mouse and the coordinates of the points of the points
of R, G, B three-color value.
Ⅱ、the image format
A support of the image data format of eight and 24-bit color
images.
B after the value of the image is actually only 0 and 255 of the
eight images, the value of the image format is the trick behind the
morphology of particles and image formats, an image of the image
format does not support.
Ⅲ、Measurement Tools
1、click tools that the left mouse button click OK.
2、 line the left mouse button click twice determine a line,
right-click Cancel.
3、straight-line click the left mouse button twice determine a line,
right-click Cancel.
4、 2points round the left mouse button click twice, through the
designation of central and determine the radius circle, right-been
cancelled.
5、three points three times round the left mouse button click,
through the designated circle on the three identified yen (3:00
uniform, with a round of high precision), right-click Cancel.
6、Arc the left mouse button click three times. Left-click the first
round starting point, left-click end of the second round,
left-click on the third point arc. Right-click Cancel.
7、5 points rectangular click the left mouse button identified five
rectangular, left the first left-click the second time the first
set of rectangular side, left-click III, IV and V are the edge of
the other three , Right-click Cancel.
8、more than several times in the deformation of the mouse click,
right-click + SHIFT more deformation closed, right-click Cancel.
Polygon area measuring only measurement convex polygon, concave
polygon area of the current measurement can not be completed. Can
also measure the perimeter.
9、three points elliptical mouse click in the third, were identified
center, the long axis, the short axis, right-click Cancel.
10、 character tools, click the mouse twice identified tagging
region, determine the location marked, right-click Cancel, the
image on eBay. Ⅳ、
1、middle-line mouse respectively click select the angle between the two side
(can be on both sides of the line, straight edge and rectangular),
the third click OK middle-line position. Right-click Cancel.
2、vertical lines need to click the left mouse button twice, first click to select
segment, linear or rectangular side, the second click OK vertical
position, right-click Cancel.
3、parallel lines need to click the left mouse button twice, first click to select
segment, linear or rectangular side, the second click OK parallel
line position, right-click Cancel.
4、Tangent on a round on the need to click the left mouse button twice, click to select
the first round, second click OK tangent position, right-click
Cancel.
5、Outside the circle tangent need to click the left mouse button three times, |
